发布时间：
Materials Letters材料快报
你的格式必须参考materialsletters期刊的guidelines，严格按照其要求更改你的论文可以找个有经验的人帮你润色一下,再看看通篇是不是有描述不清或者语法问题首先编辑指出你的文章语言不符合该杂志的要求，除非你经过大修之后或者重新写作，满足杂志要求后，在重投该杂志。好好找人修改语言问题吧
我们知道SCI期刊“Materials Letters”投稿格式审查严格，要求很高，但投稿指南上说的又不是面面俱到，所以让人很是头疼。现将Materials Letters投稿格式总结如下: (说明:本文以接收,格式审查不存在问题；abcdefg代替为文章具体内容) abcdefg-------（文章题目） 作者1a, b,作者2a, b,作者3a, b, *（作者） College --------, ---- University, city, 066---, China --------, --- University,city, 066---, China -------,---- Road,----, -----,45678,USA * Corresponding author: T:+86-1234-0123456; E-mail: Abstract:In this paper, the ----- of -------------abcdefg Keyword: Micro----; -------；------；------；------ Introduction The precipitation hardening ---------alloys are extensively used in the ------- structural -----------abcdefg abcdefg--------------abcdefg abcdefg--------------abcdefg Materials and methods The composition of the experimental ----------abcdefg Vickers microhardness was ---------abcdefg F 1 Results and discussions After -------------------abcdefg F 2 The ----------------abcdefg A comparison -----------abcdefg F 3 abcdefg-----------abcdefg F 4 Why abcdefg--------------abcdefg（分析） Our study abcdefg Conclusions In summary, processing----------abcdefg Acknowledgments The authors would like to -----------abcdefg References [1] BergLK, GjønnesJ, HansenV, LiXZ, Knutson-WedelM, WaterlooG, et Acta Mater2001;49:3443- [2] XiaoYP, PanQL, LiWB, LiuXY, HeYB Mater Des2011;32:2149- Figures Figure captions F 1 abcdefg F 2 abcdefg F 3 abcdefg F 4 abcdefg
材料类文章的影响因子一般都比较高，比如AFM和AM算是材料领域里较好的杂志，最近公布的影响因子分别为486和857。chemistryofmaterials也是材料领域里不错的杂志，影响因子为397，另外journalofmaterialchemistry影响因子为099，microporousmesoporousmaterials影响因子为22，因此影响因子在0左右的只能算材料领域里非常一般的杂志了，比如materialsletters（影响因子177），还有如materialsresearchbulletin(影响因子为145）等。
我们知道SCI期刊“Materials Letters”投稿格式审查严格，要求很高，但投稿指南上说的又不是面面俱到，所以让人很是头疼。现将Materials Letters投稿格式总结如下: (说明:本文以接收,格式审查不存在问题；abcdefg代替为文章具体内容) abcdefg-------（文章题目） 作者1a, b,作者2a, b,作者3a, b, *（作者） College --------, ---- University, city, 066---, China --------, --- University,city, 066---, China -------,---- Road,----, -----,45678,USA * Corresponding author: T:+86-1234-0123456; E-mail: Abstract:In this paper, the ----- of -------------abcdefg Keyword: Micro----; -------；------；------；------ Introduction The precipitation hardening ---------alloys are extensively used in the ------- structural -----------abcdefg abcdefg--------------abcdefg abcdefg--------------abcdefg Materials and methods The composition of the experimental ----------abcdefg Vickers microhardness was ---------abcdefg F 1 Results and discussions After -------------------abcdefg F 2 The ----------------abcdefg A comparison -----------abcdefg F 3 abcdefg-----------abcdefg F 4 Why abcdefg--------------abcdefg（分析） Our study abcdefg Conclusions In summary, processing----------abcdefg Acknowledgments The authors would like to -----------abcdefg References [1] BergLK, GjønnesJ, HansenV, LiXZ, Knutson-WedelM, WaterlooG, et Acta Mater2001;49:3443- [2] XiaoYP, PanQL, LiWB, LiuXY, HeYB Mater Des2011;32:2149- Figures Figure captions F 1 abcdefg F 2 abcdefg F 3 abcdefg F 4 abcdefg
Short Communications (Letters) are intended as brief reports of significant, original and timely research results on the science, applications and processing of materials which warrant In considering a manuscript for publication, particular attention will be given to the originality of the research, the desirability of speedy publication, the clarity of the presentation andthe validity of the There is a strict four-page limit to printed Manuscriptsmust not exceed 2000 words plus three figures and one This includes everything: the title,authors, affiliations, abstract, keywords, body of the manuscript, acknowledgements, references,figure captions, The maximum number of figures is strictly limited to If the maximum of4 figures is used, then the total number of words must be reduced to If the maximum of 5figures is used, then the total number of words must be reduced to If more than 5 figures areused, the manuscript will be The manuscript submitted for review should not exceed8 pages (including title, abstract, references, figures, tables and figure captions) ShortCommunications need to report a concise but exhaustive Material and methods section included inthe main