论文文献jdm

参考文献类型标识：专著[M]；期刊[J]；论文集[c]；学位论文[D]；标准[S]；报告[R]；专利[P]；报纸[N]；J表示期刊文章——JournalM表示专著——Mongraph（以上内容来源于学术堂）

基于WIN CE的ADSL线路参数研究ADSL line parameters research based on WIN CE CE (also known officially as Windows Embedded CE since version [2][3], and sometimes abbreviated WinCE) is a variation of Microsoft's Windows operating system for minimalistic computers and embedded systems. Windows CE is a distinctly different kernel, rather than a trimmed-down version of desktop Windows. It is not to be confused with Windows XP Embedded which is NT-based. It is supported on Intel x86 and compatibles, MIPS, ARM, and Hitachi SuperH CE is optimized for devices that have minimal storage—a Windows CE kernel may run in under a megabyte of memory. Devices are often configured without disk storage, and may be configured as a “closed” system that does not allow for end-user extension (for instance, it can be burned into ROM). Windows CE conforms to the definition of a real-time operating system, with a deterministic interrupt latency. It supports 256 priority levels and uses priority inheritance for dealing with priority inversion. The fundamental unit of execution is the thread. This helps to simplify the interface and improve execution has stated that the ‘CE’ is not an intentional initialism, but many people believe CE stands for ‘Consumer Electronics’ or ‘Compact Edition’; users often disparagingly called it “Wince”.[4] Microsoft says it implies a number of Windows CE design precepts, including “Compact, Connectable, Compatible, Companion, and Efficient.”[5] The first version, known during development under the codename “Pegasus”, featured a Windows-like GUI and a number of Microsoft's popular applications, all trimmed down for smaller storage, memory, and speed of the palmtops of the then, Windows CE has evolved into a component-based, embedded, real-time operating system. It is no longer targeted solely at hand-held computers. Many platforms have been based on the core Windows CE operating system, including Microsoft's AutoPC, Pocket PC 2000, Pocket PC 2002, Windows Mobile 2003, Windows Mobile 2003 SE, Windows Mobile , Windows Mobile 6, Smartphone 2002, Smartphone 2003 and many industrial devices and embedded systems. Windows CE even powered select games for the Sega Dreamcast, was the operating system of the controversial Gizmondo handheld, and can partially run on modified Microsoft Xbox game distinctive feature of Windows CE compared to other Microsoft operating systems is that large parts of it are offered in source code form. First, source code was offered to several vendors, so they could adjust it to their hardware. Then products like Platform Builder (an integrated environment for Windows CE OS image creation and integration, or customized operating system designs based on CE) offered several components in source code form to the general public. However, a number of core components that do not need adaptation to specific hardware environments (other than the CPU family) are still distributed in binary form toolsVisual StudioLate versions of Microsoft Visual Studio support projects for Windows CE / Windows Mobile, producing executable programs and platform images either as an emulator or attached by cable to an actual mobile device. A mobile device is not necessary to develop a CE program. The .NET Compact Framework supports a subset of the .NET Framework with projects in C# and , but not Managed C++.Platform BuilderThis programming tool is used for building the platform (BSP + Kernel), device drivers (shared source or custom made) and also the application. This is a one step environment to get the system up and running. One can also use Platform Builder to export an SDK (standard development kit) for the target microprocessor (SuperH, x86, MIPS, ARM etc.) to be used with another associated tool set named Visual C++ (eVC)The Embedded Visual C++ tool is for development of embedded application for Windows CE based devices. This tool can be used standalone using the SDK exported from Platform Builder or using the Platform Builder using the Platform Manager connectivity to Windows Mobile, Pocket PC, and SmartPhoneOften Windows CE, Windows Mobile, and Pocket PC are used interchangeably. This practice is not entirely accurate. Windows CE is a modular/componentized operating system that serves as the foundation of several classes of devices. Some of these modules provide subsets of other components' features (. varying levels of windowing support; DCOM vs COM), others which are mutually exclusive (Bitmap or TrueType font support), and others which add additional features to another component. One can buy a kit (the Platform Builder) which contains all these components and the tools with which to develop a custom platform. Applications such as Excel Mobile/Pocket Excel are not part of this kit. The older Handheld PC version of Pocket Word and several other older applications are included as samples, Mobile is best described as a subset of platforms based on a Windows CE underpinning. Currently, Pocket PC (now called Windows Mobile Classic), SmartPhone (Windows Mobile Standard), and PocketPC Phone Edition (Windows Mobile Professional) are the three main platforms under the Windows Mobile umbrella. Each platform utilizes different components of Windows CE, as well as supplemental features and applications suited for their respective PC and Windows Mobile is a Microsoft-defined custom platform for general PDA use, and consists of a Microsoft-defined set of minimum profiles (Professional Edition, Premium Edition) of software and hardware that is supported. The rules for manufacturing a Pocket PC device are stricter than those for producing a custom Windows CE-based platform. The defining characteristics of the Pocket PC are the digitizer as the primary Human Interface Device and its extremely portable SmartPhone platform is a feature rich OS and interface for cellular phone handsets. SmartPhone offers productivity features to business users, such as email, as well as multimedia capabilities for consumers. The SmartPhone interface relies heavily on joystick navigation and PhonePad input. Devices running SmartPhone do not include a touchscreen interface. SmartPhone devices generally resemble other cellular handset form factors, whereas most Phone Edition devices use a PDA form factor with a larger Mobile 5 supports USB and new devices running this OS will also conform to the USB Mass Storage Class, meaning the storage on PPC can be accessed from any USB-equipped PC, without requiring any extra software, except requiring a compliant host. In other words, you can use it as a flash productsCompetitors to consumer CE based PDA platforms like Pocket PC – the main application of Windows CE – are Java, Symbian OS, Palm OS, iPhone OS and Linux based packages like Qtopia Embedded Linux environment from Trolltech, Convergent Linux Platform from a La Mobile, and Access Linux Platform from Orange and secondary usage of CE is in devices in need of graphical user interfaces, (point of sale terminals, media centers, web tablets, thin clients) as the main selling point CE is the look and feel being similar to desktop Windows. The competition is Windows XP, Linux and graphical packages for simpler embedded operating an RTOS, Windows CE is also theoretically a competitor to any realtime operating system in the embedded space, like VxWorks, ITRON or eCos. The dominating method, however, of mixing Windows look and feel with realtime on the same hardware, is to run double operating systems using some virtualization technology, like TRANGO Hypervisor from TRANGO Virtual Processors or Intime from TenAsys in the case of Windows, and OS Ware from VirtualLogix, Padded Cell from Green Hills Software, OKL4 from Open Kernel Labs, TRANGO Hypervisor from TRANGO Virtual Processors, RTS Hypervisor from Real-Time Systems or PikeOS from Sysgo, in case of the Digital Subscriber Line (ADSL) is a form of DSL, a data communications technology that enables faster data transmission over copper telephone lines than a conventional voiceband modem can provide. It does this by utilizing frequencies that are not used by a voice telephone call. A splitter - or microfilter - allows a single telephone connection to be used for both ADSL service and voice calls at the same time. Because phone lines vary in quality and were not originally engineered with DSL in mind, it can generally only be used over short distances, typically less than 3mi ( km) [William Stallings' book].At the telephone exchange the line generally terminates at a DSLAM where another frequency splitter separates the voice band signal for the conventional phone network. Data carried by the ADSL is typically routed over the telephone company's data network and eventually reaches a conventional internet network. In the UK under British Telecom the data network in question is its ATM network which in turn sends it to its IP network IP distinguishing characteristic of ADSL over other forms of DSL is that the volume of data flow is greater in one direction than the other, . it is asymmetric. Providers usually market ADSL as a service for consumers to connect to the Internet in a relatively passive mode: able to use the higher speed direction for the "download" from the Internet but not needing to run servers that would require high speed in the other are both technical and marketing reasons why ADSL is in many places the most common type offered to home users. On the technical side, there is likely to be more crosstalk from other circuits at the DSLAM end (where the wires from many local loops are close to each other) than at the customer premises. Thus the upload signal is weakest at the noisiest part of the local loop, while the download signal is strongest at the noisiest part of the local loop. It therefore makes technical sense to have the DSLAM transmit at a higher bit rate than does the modem on the customer end. Since the typical home user in fact does prefer a higher download speed, the telephone companies chose to make a virtue out of necessity, hence ADSL. On the marketing side, limiting upload speeds limits the attractiveness of this service to business customers, often causing them to purchase higher cost Digital Signal 1 services instead. In this fashion, it segments the digital communications market between business and home usersHow ADSL worksOn the wireCurrently, most ADSL communication is full duplex. Full duplex ADSL communication is usually achieved on a wire pair by either frequency division duplex (FDD), echo canceling duplex (ECD), or time division duplexing (TDD). FDM uses two separate frequency bands, referred to as the upstream and downstream bands. The upstream band is used for communication from the end user to the telephone central office. The downstream band is used for communicating from the central office to the end user. With standard ADSL (annex A), the band from kHz to 138 kHz is used for upstream communication, while 138 kHz – 1104 kHz is used for downstream communication. Each of these is further divided into smaller frequency channels of kHz. During initial training, the ADSL modem tests which of the available channels have an acceptable signal-to-noise ratio. The distance from the telephone exchange, noise on the copper wire, or interference from AM radio stations may introduce errors on some frequencies. By keeping the channels small, a high error rate on one frequency thus need not render the line unusable: the channel will not be used, merely resulting in reduced throughput on an otherwise functional ADSL may support usage of higher frequencies as a proprietary extension to the standard. However, this requires matching vendor-supplied equipment on both ends of the line, and will likely result in crosstalk issues that affect other lines in the same is a direct relationship between the number of channels available and the throughput capacity of the ADSL connection. The exact data capacity per channel depends on the modulation method used.[edit] ModulationADSL initially existed in two flavours (similar to VDSL), namely CAP and DMT. CAP was the de facto standard for ADSL deployments up until 1996, deployed in 90 percent of ADSL installs at the time. However, DMT was chosen for the first ITU-T ADSL standards, and (also called and respectively). Therefore all modern installations of ADSL are based on the DMT modulation J and M shift the upstream/downstream frequency split up to 276 kHz (from 138 kHz used in the commonly deployed annex A) in order to boost upstream rates. Additionally, the "all-digital-loop" variants of ADSL2 and ADSL2+ (annexes I and J) support an extra 256 kbit/s of upstream if the bandwidth normally used for POTS voice calls is allocated for ADSL the ADSL access utilizes the MHz band, ADSL2+ utilizes the MHz downstream and upstream rates displayed are theoretical maxima. Note also that because Digital subscriber line access multiplexers and ADSL modems may have been implemented based on differing or incomplete standards some manufacturers may advertise different speeds. For example, Ericsson has several devices that support non-standard upstream speeds of up to 2 Mbit/s in ADSL2 and ADSL2+.[edit] Installation issuesDue to the way it uses the frequency spectrum, ADSL deployment presents some issues. It is necessary to install appropriate frequency filters at the customer's premises, to avoid interferences with the voice service, while at the same time taking care to keep a clean signal level for the ADSL the early days of DSL, installation required a technician to visit the premises. A splitter was installed near the demarcation point, from which a dedicated data line was installed. This way, the DSL signal is separated earlier and is not attenuated inside the customer premises. However, this procedure is costly, and also caused problems with customers complaining about having to wait for the technician to perform the installation. As a result, many DSL vendors started offering a self-install option, in which they ship equipment and instructions to the customer. Instead of separating the DSL signal at the demarcation point, the opposite is done: the DSL signal is "filtered off" at each phone outlet by use of a low pass filter, also known as microfilter. This method does not require any rewiring inside the customer side effect of the move to the self-install model is that the DSL signal can be degraded, especially if more than 5 voiceband devices are connected to the line. The DSL signal is now present on all telephone wiring in the building, causing attenuation and echo. A way to circumvent this is to go back to the original model, and install one filter upstream from all telephone jacks in the building, except for the jack to which the DSL modem will be connected. Since this requires wiring changes by the customer and may not work on some household telephone wiring, it is rarely done. It is usually much easier to install filters at each telephone jack that is in use.

Journal 杂志 期刊 论文Master 硕士 论文Doctor 博士 论文望采纳。

注：英文的文献标识码应与中文对应。[参考文献类型标识码]M专著Monograph；C-论文集Collection；N报纸文章News；J期刊文章Journal；D学位论文Degree；R报告Report；S标准Standard；P专利Patent；A专著、论文集中的析出文献Article；Z其它末说明文献（1）文献类型标识：专著[M]；期刊[J]；论文集[c]；学位论文[D]；标准[S]；报告[R]；专利[P]；报纸[N]；（2）电子文献类型标识：数据库[DB]；计算机程序[CP]；电子公告[EB]；（3）电子文献的载体类型及其标识：联机网上数据库[DB／OL]；国家期刊出版格式要求在中图分类号的下面应标出文献标识码，规定如下：作者可从下列A、B、C、D、E中选用一种标识码来揭示文章的性质：A理论与应用研究学术论文（包括综述报告）；B实用性成果报告（科学技术）、理论学习与社会实践总结（科技）；C业务指导与技术管理的文章（包括特约评论）；D一般性通讯、报导、专访等；E文件、资料、人物、书刊、知识介绍等。注：英文的文献标识码应与中文对应。[参考文献类型标识码]M专著Monograph；C-论文集Collection；N报纸文章News；J期刊文章Journal；D学位论文Degree；R报告Report；S标准Standard；P专利Patent；A专著、论文集中的析出文献Article；Z其它末说明文献（1）文献类型标识：专著[M]；期刊[J]；论文集[c]；学位论文[D]；标准[S]；报告[R]；专利[P]；报纸[N]；（2）电子文献类型标识：数据库[DB]；计算机程序[CP]；电子公告[EB]；（3）电子文献的载体类型及其标识：联机网上数据库[DB／OL]；

期刊[J] 专著[M] 论文集[C] 学位论文[D] 专利[P] 标准[S] 报纸[N] 学术报告[R] 磁带[MT] 磁盘[DK] 光盘[CD] 联机网络[OL] 网上数据库[DB/OL] 光盘图书[M/CD] 磁带数据库[DB/MT] 磁盘软件[CP/DK] 网上期刊[J/OL] 网上电子公告[EB/OL]

百度学术可以找到参考文献,输入关键词，在输入年份，就能找到相对应的参考文献。如果不知道参考文献格式要求，可以百度搜，参考文献自动生成器。直接按着填就出来了。百度搜索参考文献自动生成器，按着里面填，点生成参考文献就出来了。参考文献标准格式参考文献类型：专著［M］，论文集［C］，报纸文章［N］，期刊文章［J］，学位论文［D］，报告［R］，标准［S］，专利［P］，论文集中的析出文献［A］电子文献类型：数据库［DB］，计算机［CP］，电子公告［EB］电子文献的载体类型：互联网［OL］，光盘［CD］，磁带［MT］，磁盘［DK］A：专著、论文集、学位论文、报告［序号］主要责任者.文献题名［文献类型标识］.出版地：出版者，出版年.起止页码（可选）［1］刘国钧，陈绍业.图书馆目录［M］.北京：高等教育出版社，:期刊文章［序号］主要责任者.文献题名［J］.刊名，年，卷（期）：起止页码［1］何龄修.读南明史［J］.中国史研究，1998,(3):167-173.［2］OUJP，SOONGTT，［J］.EarthquackEng,1997,38(3)::论文集中的析出文献［序号］析出文献主要责任者.析出文献题名［A］.原文献主要责任者（可选）.原文献题名［C］.出版地：出版者，出版年.起止页码［7］钟文发.非线性规划在可燃毒物配置中的应用［A］.赵炜.运筹学的理论与应用——中国运筹学会第五届大会论文集［C］.西安：西安电子科技大学出版社，：报纸文章［序号］主要责任者.文献题名［N］.报纸名，出版日期（版次）［8］谢希德.创造学习的新思路［N］.人民日报，1998-12-25（10）.E：电子文献[文献类型/载体类型标识]：[J/OL]网上期刊、[EB/OL]网上电子公告、[M/CD]光盘图书、[DB/OL]网上数据库、[DB/MT]磁带数据库［序号］主要责任者.电子文献题名［电子文献及载体类型标识］.电子文献的出版或获得地址，发表更新日期/引用日期［12］王明亮.关于中国学术期刊标准化数据库系统工程的进展［8］万锦.中国大学学报文摘（1983-1993）.英文版［DB/CD］.北京：中国大百科全书出版社，1996.作者.题名[D].所在城市:保存单位,发布年份.李琳.住院烧伤患者综合健康状况及其影响因素研究[D].福州:福建医科大学,2009.其他的：作者.题名[J].刊名,年,卷(期):起止页码.沈平,彭湘粤,黎晓静,等.临床路径应用于婴幼儿呼吸道异物手术后的效果[J].中华护理杂志,2012,47(10):930-932.作者.书名[M].版次.出版地:出版者,出版年:起止页码.胡雁.护理研究[M].第4版.北京:人民卫生出版社,2012:38.作者.题名[N].报纸名,出版日期(版次).丁文祥.数字革命与国际竞争[N].中国青年报,2000-11-20(15).作者.题名[EB/OL].网址,发表日期/引用日期(任选).世界卫生组织.关于患者安全的10个事实[EB/OL].其他：[R]、[P]、[A]、[C]、[Z]等。