装配式钢结构论文英文参考文献

英文论文参考文献格式如下：

一、学术论文英文参考文献标注格式

按照现行规定，学术期刊中论文参考文献的标注采用顺序编码制，即在文内的引文处按引用文献在论文中出现的先后顺序以阿拉伯数字连续编码，序号置于方括号内。同一文献在一文中被反复引用者，用同一序号标示。

这一规定使得所列文献简洁明了，应该引起论文作者注意。英文参考文献和中文参考文献一样，按在文中出现的先后顺序与中文文献混合连续编码著录;英文文献用印刷体；英文书名、期刊名和报纸名等用斜体；所列项目及次序与中文文献相同，但文献类型可不标出；忌用中文叙述英文。其格式为：

专著、论文集、学位论文、报告主要责任者。文献题名。出版地：出版者，出版年。起止页码。示例：Day,C.,Veen, Walraven,G. Children and youth at risk and urban education. Research, policy and prac-tice. Leuven/Apeldoorn:Garant. 1997.

期刊文章：主要责任者。文献题名。刊名，年，卷(期)：起止页码。示例：Driessen,G.,& Van der Grinten,M. Home language proficiency in the Netherland:The evaluation of Turkish andMoroccan bilingual programmes- A critical review, Studies in Educational Evaluation,1994, 20(3)：365- 386.

论文集中的析出文献析出文献主要责任者。析出文献题名。原文献主要责任者(任选)。原文献题名。出版地：出版者，出版年。析出文献起止页码。

示例：Driessen,G.,Mulder,L.,& Jungbluth,P. Structural and cultural determinants of educational opportunities in theNetherlands. In (Ed.)，Root and migration in global perspective. Jerusalem:Magnes . 104.

二、关于英文人名的标注

现行编排规范对英文人名如何标注未作明确要求，英文人名的标注较为混乱，有标注全名的，有标注时将名缩写、姓不缩写、保持原来顺序的，还有在姓、名之间加圆点的，后者是我国翻译作品中，中文书写外国人名经常采用的一种方式。

其实，标注英文人名是有章可循的，在国外学术著作的参考文献中，关于人名的标注已约定俗成为一种统一的格式，即英文参考文献标注作者姓名时，要求姓在前、名在后，姓与名之间用逗号隔开，姓的词首字母大写，其余字母不大写;名用词首大写字母表示，后加缩写符号圆点，缩写符号不可省略。由于欧美国家人的姓名排列一般是名在前、姓在后，在标注时必须加以调整。如Georg Paghet Thomson，前面两个词是名，最后一个词是姓，应标注为Thomson,G. P为什么要如此标注呢？

1. 在应用计算机等信息工具进行英文文献检索时，以英文作者姓名中的姓作为依据之一，即以姓作为检索目标之一。

2. 在欧美人姓名表达含义里，姓比名的重要性更强、更正式。用姓而不是名来代表作者，还有尊重、礼貌的意味。名缩写后加缩写符号圆点，也含有正式、尊重和礼貌的意味，缩写符号不可省略。

3. 表示与平常书写姓名的不同，体现学术论文重要性、简约性和准确性的要求，符合科研论文文体风格。这种标注在英文学术著作、科技文献中已广泛采用，也容易被广大读者、作者理解、接受。

对于复姓情况，如Jory Albores-Saavedra等，在引用标注时，应将复姓全部写出，即Albores-Saavedra, J对于姓前带有冠词或介词的情况，如带有Mac,Le,Von,Van den等，标注时不能省略，应同姓一起提到前面标注，如Mac Donald,La Fontaina,Von Eschenbach,Van den Bery等。

一个参考文献有两位或两位以上作者时，标注时除按上述要求将每位作者的姓提前书写外，作者与作者之间用逗号分开，最后一位作者前加&符号，如示例[1],也可仅保留前三位作者，之后加etc.表示。

英文参考文献的标准格式 按照字面的意思，参考文献是文章或著作等写作过程中参考过的文献。接下来由我为大家整理出英文参考文献的标准格式，仅供参考，希望能够帮助到大家！ 题目：应简洁、明确、有概括性。 关键词：从论文标题或正文中挑选3～5个最能表达主要内容的词作为关键词。 摘要：（150字）要有高度的概括力，语言精练、明确，交代本文的主要内容和观点。 目录：写出目录，标明页码。编写提纲的步骤： （一）确定论文提要，再加进材料，形成全文的概要 论文提要是内容提纲的雏型。一般书、教学参考书都有反映全书内容的提要，以便读者一翻提要就知道书的`大概内容。我们写论文也需要先写出论文提要。在执笔前把论文的题目和大标题、小标题列出来，再把选用的材料插进去，就形成了论文内容的提要。 论文提纲可分为简单提纲和详细提纲两种。简单提纲是高度概括的，只提示论文的要点，如何展开则不涉及。这种提纲虽然简单，但由于它是经过深思熟虑构成的，写作时能顺利进行。没有这种准备，边想边写很难顺利地写下去。 引言（绪论）（300字左右） 引言是论文的开头部分，主要说明论文写作的目的、现实意义、对所研究问题的认识，并提出论文的中心论点等。数据恢复前言要写得简明扼要，篇幅不要太长。 正文（5000左右）分析问题，论证观点，尽量反映出自己的科研能力和学术水平。 第1章 某某现状（归纳存在的主要问题并论证问题的存在及其影响） 把脉 . . . …… 第2章 问题产生的原因分析（归纳成因并论证） 诊断 . . …… 第3章 解决问题的对策（治理问题的途径和方法） 治疗 . . …… 第4章 结论（300左右），简要归纳全文的中心和主要结论毕业论文的收尾部分，是围绕本论所作的结束语。其基本的要点就是总结全文，加深题意。 （注意：修改后的论文提纲要写出章和节的内容，节的内容自己定，写论文时要将内容丰富起来，要达到5000字的字数要求） 致谢辞：简述自己通过做毕业论文的体会，并应对指导教师和协助完成论文的有关人员表示谢意。 参考文献：在毕业论文末尾要列出在论文中参考过的专著、论文及其他资料，所列参考文献应按文中参考或引证的先后顺序排列。 ;

随便弄弄吧 我当然就是用翻译器翻的，然后自己改改，反正老师也看不懂，没特别明显的错误就好了，还要跟老师打好关系，会让你过的

太长了，超过了10000字发不了。我这里先给你个英文的你加我QQ我给你中文的两部分不会弄，你加我QQ我发给你吧，加分啊395886292 <英文版> Talling building and Steel construction Although there have been many advancements in building construction technology in general. Spectacular archievements have been made in the design and construction of ultrahigh-rise buildings. The early development of high-rise buildings began with structural steel concrete and stressed-skin tube systems have since been economically and competitively used in a number of structures for both residential and commercial high-rise buildings ranging from 50 to 110 stories that are being built all over the United States are the result of innovations and development of new structual systems. Greater height entails increased column and beam sizes to make buildings more rigid so that under wind load they will not sway beyond an acceptable lateral sway may cause serious recurring damage to partitions, other architectural details. In addition,excessive sway may cause discomfort to the occupants of the building because their perception of such systems of reinforced concrete,as well as steel,take full advantage of inherent potential stiffness of the total building and therefore require additional stiffening to limit the sway. In a steel structure,for example,the economy can be defined in terms of the total average quantity of steel per square foot of floor area of the A in Fig .1 represents the average unit weight of a conventional frame with increasing numbers of stories. Curve B represents the average steel weight if the frame is protected from all lateral loads. The gap between the upper boundary and the lower boundary represents the premium for height for the traditional column-and-beam engineers have developed structural systems with a view to eliminating this premium. Systems in steel. Tall buildings in steel developed as a result of several types of structural innovations. The innovations have been applied to the construction of both office and apartment buildings. Frame with rigid belt trusses. In order to tie the exterior columns of a frame structure to the interior vertical trusses,a system of rigid belt trusses at mid-height and at the top of the building may be used. A good example of this system is the First Wisconsin Bank Building(1974) in Milwaukee. Framed tube. The maximum efficiency of the total structure of a tall building, for both strength and stiffness,to resist wind load can be achieved only if all column element can be connected to each other in such a way that the entire building acts as a hollow tube or rigid box in projecting out of the ground. This particular structural system was probably used for the first time in the 43-story reinforced concrete DeWitt Chestnut Apartment Building in Chicago. The most significant use of this system is in the twin structural steel towers of the 110-story World Trade Center building in New York Column-diagonal truss tube. The exterior columns of a building can be spaced reasonably far apart and yet be made to work together as a tube by connecting them with diagonal members interesting at the centre line of the columns and beams. This simple yet extremely efficient system was used for the first time on the John Hancock Centre in Chicago, using as much steel as is normally needed for a traditional 40-story building. Bundled tube. With the continuing need for larger and taller buildings, the framed tube or the column-diagonal truss tube may be used in a bundled form to create larger tube envelopes while maintaining high efficiency. The 110-story Sears Roebuck Headquarters Building in Chicago has nine tube, bundled at the base of the building in three rows. Some of these individual tubes terminate at different heights of the building, demonstrating the unlimited architectural possibilities of this latest structural concept. The Sears tower, at a height of 1450 ft(442m), is the world’s tallest building. Stressed-skin tube system. The tube structural system was developed for improving the resistance to lateral forces (wind and earthquake) and the control of drift (lateral building movement ) in high-rise building. The stressed-skin tube takes the tube system a step further. The development of the stressed-skin tube utilizes the façade of the building as a structural element which acts with the framed tube, thus providing an efficient way of resisting lateral loads in high-rise buildings, and resulting in cost-effective column-free interior space with a high ratio of net to gross floor area. Because of the contribution of the stressed-skin façade, the framed members of the tube require less mass, and are thus lighter and less expensive. All the typical columns andspandrel beams are standard rolled shapes,minimizing the use and cost of special built-up members. The depth requirement for the perimeter spandrel beams is also reduced, and the need for upset beams above floors, which would encroach on valuable space, is minimized. The structural system has been used on the 54-story One Mellon Bank Center in Pittburgh. Systems in concrete. While tall buildings constructed of steel had an early start, development of tall buildings of reinforced concrete progressed at a fast enough rate to provide a competitive chanllenge to structural steel systems for both office and apartment buildings. Framed tube. As discussed above, the first framed tube concept for tall buildings was used for the 43-story DeWitt Chestnut Apartment Building. In this building ,exterior columns were spaced at () centers, and interior columns were used as needed to support the 8-in . -thick (20-m) flat-plate concrete slabs. Tube in tube. Another system in reinforced concrete for office buildings combines the traditional shear wall construction with an exterior framed tube. The system consists of an outer framed tube of very closely spaced columns and an interior rigid shear wall tube enclosing the central service area. The system (Fig .2), known as the tube-in-tube system , made it possible to design the world’s present tallest (714ft or 218m)lightweight concrete building ( the 52-story One Shell Plaza Building in Houston) for the unit price of a traditional shear wall structure of only 35 stories. Systems combining both concrete and steel have also been developed, an examle of which is the composite system developed by skidmore, Owings &Merril in which an exterior closely spaced framed tube in concrete envelops an interior steel framing, thereby combining the advantages of both reinforced concrete and structural steel systems. The 52-story One Shell Square Building in New Orleans is based on this system. Steel construction refers to a broad range of building construction in which steel plays the leading role. Most steel construction consists of large-scale buildings or engineering works, with the steel generally in the form of beams, girders, bars, plates, and other members shaped through the hot-rolled process. Despite the increased use of other materials, steel construction remained a major outlet for the steel industries of the , , , Japan, West German, France, and other steel producers in the 1970s Early history. The history of steel construction begins paradoxically several decades before the introduction of the Bessemer and the Siemens-Martin (openj-hearth) processes made it possible to produce steel in quantities sufficient for structure use. Many of problems of steel construction were studied earlier in connection with iron construction, which began with the Coalbrookdale Bridge, built in cast iron over the Severn River in England in 1777. This and subsequent iron bridge work, in addition to the construction of steam boilers and iron ship hulls , spurred the development of techniques for fabricating, designing, and jioning. The advantages of iron over masonry lay in the much smaller amounts of material required. The truss form, based on the resistance of the triangle to deformation, long used in timber, was translated effectively into iron, with cast iron being used for compression , those bearing the weight of direct loading-and wrought iron being used for tension , those bearing the pull of suspended loading. The technique for passing iron, heated to the plastic state, between rolls to form flat and rounded bars, was developed as early as 1800;by 1819 angle irons were rolled; and in 1849 the first I beams, feet () long , were fabricated as roof girders for a Paris railroad station. Two years later Joseph Paxton of England built the Crystal Palace for the London Exposition of 1851. He is said to have conceived the idea of cage construction-using relatively slender iron beams as a skeleton for the glass walls of a large, open structure. Resistance to wind forces in the Crystal palace was provided by diagonal iron rods. Two feature are particularly important in the history of metal construction; first, the use of latticed girder, which are small trusses, a form first developed in timber bridges and other structures and translated into metal by Paxton ; and second, the joining of wrought-iron tension members and cast-iron compression members by means of rivets inserted while hot. In 1853 the first metal floor beams were rolled for the Cooper Union Building in New York. In the light of the principal market demand for iron beams at the time, it is not surprising that the Cooper Union beams closely resembled railroad rails. The development of the Bessemer and Siemens-Martin processes in the 1850s and 1860s suddenly open the way to the use of steel for structural purpose. Stronger than iron in both tension and compression ,the newly available metal was seized on by imaginative engineers, notably by those involved in building the great number of heavy railroad bridges then in demand in Britain, Europe, and the . A notable example was the Eads Bridge, also known as the St. Louis Bridge, in St. Louis (1867-1874), in which tubular steel ribs were used to form arches with a span of more than 500ft (). In Britain, the Firth of Forth cantilever bridge (1883-90) employed tubular struts, some 12 ft () in diameter and 350 ft (107m) long. Such bridges and other structures were important in leading to the development and enforcement of standards and codification of permissible design stresses. The lack of adequate theoretical knowledge, and even of an adequate basis for theoretical studies, limited the value of stress analysis during the early years of the 20th century,as iccasionally failures,such as that of a cantilever bridge in Quebec in 1907, failures were rare in the metal-skeleton office buildings;the simplicity of their design proved highly practical even in the absence of sophisticated analysis techniques. Throughout the first third of the century, ordinary carbon steel, without any special alloy strengthening or hardening, was universally used. The possibilities inherent in metal construction for high-rise building was demonstrated to the world by the Paris Exposition of which Alexandre-Gustave Eiffel, a leading French bridge engineer, erected an openwork metal tower 300m (984 ft) high. Not only was the height-more than double that of the Great Pyramid-remarkable, but the speed of erection and low cost were even more so, a small crew completed the work in a few months. The first skyscrapers. Meantime, in the United States another important development was taking place. In 1884-85 Maj. William Le Baron Jenney, a Chicago engineer , had designed the Home Insurance Building, ten stories high, with a metal skeleton. Jenney’s beams were of Bessemer steel, though his columns were cast iron. Cast iron lintels supporting masonry over window openings were, in turn, supported on the cast iron columns. Soild masonry court and party walls provided lateral support against wind loading. Within a decade the same type of construction had been used in more than 30 office buildings in Chicago and New York. Steel played a larger and larger role in these , with riveted connections for beams and columns, sometimes strengthened for wind bracing by overlaying gusset plates at the junction of vertical and horizontal members. Light masonry curtain walls, supported at each floor level, replaced the old heavy masonry curtain walls, supported at each floor level , replaced the oldheavy masonry. Though the new construction form was to remain centred almost entirely in America for several decade, its impact on the steel industry was worldwide. By the last years of the 19th century, the basic structural shapes-I beams up to 20 in. ( ) in depth and Z and T shapes of lesser proportions were readily available, to combine with plates of several widths and thicknesses to make efficient members of any required size and strength. In 1885 the heaviest structural shape produced through hot-rolling weighed less than 100 pounds (45 kilograms) per foot; decade by decade this figure rose until in the 1960s it exceeded 700 pounds (320 kilograms) per foot. Coincident with the introduction of structural steel came the introduction of the Otis electric elevator in 1889. The demonstration of a safe passenger elevator, together with that of a safe and economical steel construction method, sent building heights soaring. In New York the 286-ft () Flatiron Building of 1902 was surpassed in 1904 by the 375-ft (115-m) Times Building ( renamed the Allied Chemical Building) , the 468-ft (143-m) City Investing Company Building in Wall Street, the 612-ft (187-m) Singer Building (1908), the 700-ft (214-m) Metropolitan Tower (1909) and, in 1913, the 780-ft (232-m) Woolworth Building. The rapid increase in height and the height-to-width ratio brought problems. To limit street congestion, building setback design was prescribed. On the technical side, the problem of lateral support was studied. A diagonal bracing system, such as that used in the Eiffel Tower, was not architecturally desirable in offices relying on sunlight for illumination. The answer was found in greater reliance on the bending resistance of certain individual beams and columns strategically designed into the skeletn frame, together with a high degree of rigidity sought at the junction of the beams and columns. With today’s modern interior lighting systems, however, diagonal bracing against wind loads has returned; one notable example is the John Hancock Center in Chicago, where the external X-braces form a dramatic part of the structure’s façade. World War I brought an interruption to the boom in what had come to be called skyscrapers (the origin of the word is uncertain), but in the 1920s New York saw a resumption of the height race, culminating in the Empire State Building in the 1931. The Empire State’s 102 stories (1,250ft. [381m]) were to keep it established as the hightest building in the world for the next 40 years. Its speed of the erection demonstrated how thoroughly the new construction technique had been mastered. A depot across the bay at Bayonne, ., supplied the girders by lighter and truck on a schedule operated with millitary precision; nine derricks powerde by electric hoists lifted the girders to position; an industrial-railway setup moved steel and other material on each floor. Initial connections were made by bolting , closely followed by riveting, followed by masonry and finishing. The entire job was completed in one year and 45 days. The worldwide depression of the 1930s and World War II provided another interruption to steel construction development, but at the same time the introduction of welding to replace riveting provided an important advance. Joining of steel parts by metal are welding had been successfully achieved by the end of the 19th century and was used in emergency ship repairs during World War I, but its application to construction was limited until after World War II. Another advance in the same area had been the introduction of high-strength bolts to replace rivets in field connections. Since the close of World War II, research in Europe, the ., and Japan has greatly extended knowledge of the behavior of different types of structural steel under varying stresses, including those exceeding the yield point, making possible more refined and systematic analysis. This in turn has led to the adoption of more liberal design codes in most countries, more imaginative design made possible by so-called plastic design ?The introduction of the computer by short-cutting tedious paperwork, made further advances and savings possible.